Template:Competing Failure Modes Introduction - Revision history

Kate Racaza: Redirected page to Competing Failure Modes Analysis

2012-06-29T07:37:05Z

Redirected page to Competing Failure Modes Analysis

← Older revision		Revision as of 07:37, 29 June 2012
Line 1:		Line 1:
	~~==Introduction==~~		#REDIRECT [[Competing Failure Modes Analysis]]
	Often, a group of products will fail due to more than one failure mode. One can take the view that the products could have failed due to any one of the possible failure modes, but since an item cannot fail more than one time, there can only be one failure mode for each failed product. In this view, the failure modes compete as to which causes the failure for each particular item. This can be viewed as a series system reliability model, with each failure mode composing a block of the series system. Competing ~~failure modes analysis segregates the analyses of failure modes and then combines the results to provide an overall model for the product in question.~~

	In order to begin analyzing data sets with more than one competing failure mode, one must perform a separate analysis for each failure mode. During each of these analyses, the failure times for all other failure modes not being analyzed are considered to be suspensions. This is because the units under test would have failed at some time in the future due to the failure mode being analyzed, had the unrelated (not analyzed) mode not occurred. Thus, in this case, the information available is that the mode under consideration did not occur and the unit under consideration accumulated test time without a failure due to the mode under consideration (or a suspension due to that mode).

	Once the analysis for each separate failure mode has been completed (using the same principles as before), the resulting reliability equation for all modes is the product of the reliability equation for each mode, or:


	~~::<math>R(t)={{R}_{1}}(t)\cdot {{R}_{2}}(t)\cdot ...\cdot {{R}_{n}}(t)</math>~~


	where <math>n</math> is the total number of failure modes considered. This is the product rule for the reliability of series systems with statistically independent components, which states that the reliability for a series system is equal to the product of the reliability values of the components comprising the system. Do note that the above equation is the reliability function based on any assumed life distribution. In Weibull++ this life distribution can be either the 2-parameter Weibull, lognormal, normal or the 1-parameter exponential.

	~~'''Example 1:'''~~
	~~{{Example: Competing Failures with Two~~ Failure Modes ~~Example}}~~

Harry Guo: /* Introduction */

2012-02-21T17:18:32Z

Introduction

← Older revision		Revision as of 17:18, 21 February 2012
Line 10:		Line 10:


	where <math>n</math> is the total number of failure modes considered. This is the product rule for the reliability of series systems with statistically independent components, which states that the reliability for a series system is equal to the product of the reliability values of the components comprising the system. Do note that ~~in Eqn. (sysrel)~~ is the reliability function based on any assumed life distribution. In Weibull++ this life distribution can be either the 2-parameter Weibull, lognormal, normal or the 1-parameter exponential.		where <math>n</math> is the total number of failure modes considered. This is the product rule for the reliability of series systems with statistically independent components, which states that the reliability for a series system is equal to the product of the reliability values of the components comprising the system. Do note that the above equation is the reliability function based on any assumed life distribution. In Weibull++ this life distribution can be either the 2-parameter Weibull, lognormal, normal or the 1-parameter exponential.

	'''Example 1:'''		'''Example 1:'''
	{{Example: Competing Failures with Two Failure Modes Example}}		{{Example: Competing Failures with Two Failure Modes Example}}

Harry Guo at 16:55, 21 February 2012

2012-02-21T16:55:35Z

← Older revision		Revision as of 16:55, 21 February 2012
Line 14:		Line 14:
	'''Example 1:'''		'''Example 1:'''
	{{Example: Competing Failures with Two Failure Modes Example}}		{{Example: Competing Failures with Two Failure Modes Example}}


	~~===Plotting Competing Failure Modes===~~

	~~[[Image:lda23.4.gif\|thumb\|center\|400px\| ]]~~
	~~<math></math>~~


	When plotting competing failure modes in Weibull++, your plots can contain the combined mode line as well as the individual mode lines. The User's Guide describes how these options can be turned on or off.

Harry Guo: Created page with '==Introduction== Often, a group of products will fail due to more than one failure mode. One can take the view that the products could have failed due to any one of the possible …'

2012-02-21T16:53:58Z

Created page with '==Introduction== Often, a group of products will fail due to more than one failure mode. One can take the view that the products could have failed due to any one of the possible …'

New page

==Introduction==
Often, a group of products will fail due to more than one failure mode. One can take the view that the products could have failed due to any one of the possible failure modes, but since an item cannot fail more than one time, there can only be one failure mode for each failed product. In this view, the failure modes compete as to which causes the failure for each particular item. This can be viewed as a series system reliability model, with each failure mode composing a block of the series system. Competing failure modes analysis segregates the analyses of failure modes and then combines the results to provide an overall model for the product in question.

In order to begin analyzing data sets with more than one competing failure mode, one must perform a separate analysis for each failure mode. During each of these analyses, the failure times for all other failure modes not being analyzed are considered to be suspensions. This is because the units under test would have failed at some time in the future due to the failure mode being analyzed, had the unrelated (not analyzed) mode not occurred. Thus, in this case, the information available is that the mode under consideration did not occur and the unit under consideration accumulated test time without a failure due to the mode under consideration (or a suspension due to that mode).

Once the analysis for each separate failure mode has been completed (using the same principles as before), the resulting reliability equation for all modes is the product of the reliability equation for each mode, or:

::<math>R(t)={{R}_{1}}(t)\cdot {{R}_{2}}(t)\cdot ...\cdot {{R}_{n}}(t)</math>

where <math>n</math> is the total number of failure modes considered. This is the product rule for the reliability of series systems with statistically independent components, which states that the reliability for a series system is equal to the product of the reliability values of the components comprising the system. Do note that in Eqn. (sysrel) is the reliability function based on any assumed life distribution. In Weibull++ this life distribution can be either the 2-parameter Weibull, lognormal, normal or the 1-parameter exponential.

'''Example 1:'''
{{Example: Competing Failures with Two Failure Modes Example}}

===Plotting Competing Failure Modes===

[[Image:lda23.4.gif|thumb|center|400px| ]]
<math></math>

When plotting competing failure modes in Weibull++, your plots can contain the combined mode line as well as the individual mode lines. The User's Guide describes how these options can be turned on or off.