Template:Reliability block diagrams for failure modes: Difference between revisions

From ReliaWiki
Jump to navigation Jump to search
(Replaced content with 'Category: For Deletion')
 
Line 1: Line 1:
= Reliability Block Diagrams for Failure Modes and Other Applications =
[[Category: For Deletion]]
In this reference, most of the examples and derivations assume that each block represents a component/subassembly in a larger system.  The same methodology and principles can also be used for other applications.  For example, all derivations assume that the event under consideration is the event of failure of a component.  One can easily take this principle and apply it to failure modes for a component/subsystem or system.  To illustrate this, consider the following example.
===Example 17===
Assume that a system has five failure modes:  A, B, C, D and F.  Furthermore, assume that failure of the entire system will occur if mode A occurs, modes B and C occur simultaneously or if either modes C and D, C and F or D and F occur simultaneously.  Given the probability of occurrence of each mode, what is the probability of failure of the system?
<br>
 
Figure "Reliability block diagram for Example 17" shows the diagram for this configuration.
<br>
 
Analysis of this diagram follows the same principles as the ones presented in this chapter and can be performed in BlockSim, if desired.
 
[[Image:chp4image33.png|center|300px|<div align="center"> Electrical network diagram. </div>]]
<br>
[[Image:chp4image34.png|center|300px|<div align="center"> RBD of Electircal network diagram</div>]]
<br>
[[Image:chp4image35.png|center|300px|<div align="center"> Reliability block diagram for Example 17. </div>]]
<br>
[[Image:chp4image36.png|center|300px|<div align="center"> Reliability block diagram for Example 18.</div>]]
<br>
 
===Example 18===
Assume that a system has six failure modes: A, B, C, D, E and F.  Furthermore, assume that failure of the entire system will occur if:
<br>
:• Mode B, C or F occurs.<br>
:• Modes A and E, A and D or E and D occur.<br>
<br>
Draw the block diagram and obtain the reliability equation.
====Solution to Example 18====
The diagram is shown in Figure "Reliability block diagram for Example 18"
<br>
The reliability equation, as obtained from BlockSim is:
<br>
 
::<math>\begin{align}
{{R}_{System}}= & (-2{{R}_{A}}\cdot {{R}_{B}}\cdot {{R}_{C}}\cdot {{R}_{D}}\cdot {{R}_{2/3}}\cdot {{R}_{E}}\cdot {{R}_{F}} \\
& +{{R}_{A}}\cdot {{R}_{B}}\cdot {{R}_{C}}\cdot {{R}_{D}}\cdot {{R}_{2/3}}\cdot {{R}_{F}} \\
& +{{R}_{A}}\cdot {{R}_{B}}\cdot {{R}_{C}}\cdot {{R}_{2/3}}\cdot {{R}_{E}}\cdot {{R}_{F}} \\
& +{{R}_{B}}\cdot {{R}_{C}}\cdot {{R}_{D}}\cdot {{R}_{2/3}}\cdot {{R}_{E}}\cdot {{R}_{F}}) 
\end{align}</math>
<br>
 
The BlockSim equation includes the node reliability term  <math>{{R}_{2/3}},</math>  which cannot fail, or  <math>{{R}_{2/3}}=1</math> .  This can be removed, yielding:
 
<br>
::<math>\begin{align}
{{R}_{System}}= & (-2{{R}_{A}}\cdot {{R}_{B}}\cdot {{R}_{C}}\cdot {{R}_{D}}\cdot {{R}_{E}}\cdot {{R}_{F}} \\
& +{{R}_{A}}\cdot {{R}_{B}}\cdot {{R}_{C}}\cdot {{R}_{D}}\cdot {{R}_{F}} \\
& +{{R}_{A}}\cdot {{R}_{B}}\cdot {{R}_{C}}\cdot {{R}_{E}}\cdot {{R}_{F}} \\
& +{{R}_{B}}\cdot {{R}_{C}}\cdot {{R}_{D}}\cdot {{R}_{E}}\cdot {{R}_{F}}) 
\end{align}</math>
 
<br>

Latest revision as of 09:36, 25 July 2012