Search results

...the [https://help.reliasoft.com/reference/system_analysis System analysis reference].'' ===Static Reliability Importance===

...the [https://help.reliasoft.com/reference/system_analysis System analysis reference]''. '''Time-Dependent System Reliability for Components in Parallel'''

...rence/reliability_growth_and_repairable_system_analysis Reliability growth reference]''. ...em is equal to zero and the end time for each system is 10,000 miles. Each system is scheduled to undergo an overhaul after a certain number of miles. It has

...rence/reliability_growth_and_repairable_system_analysis Reliability growth reference]''. A one-shot system underwent reliability growth development testing for a total of 68 trials. Delayed corrective act

{{Reference Example|{{Banner RGA Reference_Examples}}|Repairable Systems Analysis}} Crow, L.H., ''Reliability Analysis for Complex Repairable Systems'', Reliability and Biometry: Statistical Analysis of Lifelength, pg. 385, 1974.

...rence/reliability_growth_and_repairable_system_analysis Reliability growth reference]''. ...e starting time for each system is equal to 0 and the ending time for each system is 2,000 hours. Calculate the maximum likelihood estimates <math>\widehat{\

...rence/reliability_growth_and_repairable_system_analysis Reliability growth reference]''. ==Repairable System Example==

...the [https://help.reliasoft.com/reference/system_analysis System analysis reference]''. '''Reliability Importance Measures for Failure Modes'''

{{DISPLAYTITLE:k-out-of-n Systems}}{{Reference Example|{{Banner BlockSim Reference Examples}}}} This data set is from example 4.6 on page 78 in the book ''Life Cycle Reliability Engineering'' by Dr. Guangbin Yang, John Wiley & Sons, 2007.

...the [https://help.reliasoft.com/reference/system_analysis System analysis reference]''. ...g the Off-Peak phase, the reliability of Block A follows W(1.5,15) and the reliability of Block B follows W(1.5,20). In the Day Shift diagram, both blocks have CM

...the [https://help.reliasoft.com/reference/system_analysis System analysis reference]''. </noinclude> ...is implies that if any ''k''-out-of-''n'' components fail (input) then the system will fail (output).

...rence/reliability_growth_and_repairable_system_analysis Reliability growth reference]''. ...10. In other words, demonstrate that the cumulative MTBF for a repairable system is less than or equal to 0.5 during a five year operating period, with 80%

...https://help.reliasoft.com/reference/life_data_analysis Life data analysis reference]''. ...ants to design a zero-failure demonstration test in order to demonstrate a reliability of 80% at a 90% confidence level. Use the non-parametric binomial method to

{{Reference Example|{{Banner BlockSim Reference Examples}}}} ...ata set is from example 11.3 on page 259 in the book, ''An Introduction to Reliability and Maintainability Engineering'', by Dr. Charles E. Ebeling, McGraw-Hill,

== Experiment Design and Analysis Reference == :[[Reliability DOE for Life Tests]]

...rence/reliability_growth_and_repairable_system_analysis Reliability growth reference].'' </noinclude> ...s in which the anomalies lie are generated independently of the underlying reliability growth process. The approach for estimating the parameters of the growth mo

...rence/reliability_growth_and_repairable_system_analysis Reliability growth reference]''. ...f the systems had a start time equal to zero and the last failure for each system corresponds to the end time. Group the data based on a fixed interval of 3,

...rence/reliability_growth_and_repairable_system_analysis Reliability growth reference]''. A one-shot system underwent reliability growth development for a total of 50 trials. The test was performed as a co

...that are relevant to the particular topic but are not appropriate for the reference book (e.g., examples that demonstrate how to perform the analysis in the so For an example of how this element has been integrated into a reference book chapter, see [[Repairable_Systems_Analysis_Through_Simulation#Discussi

<onlyinclude>Represents an Xfmea, RCM++ or RBI system hierarchy item. </onlyinclude> |HierarchyLevel||Gets the level number of the item in the system hierarchy (e.g., 1 = top-level item, 2 = second-level item, 3 = third-level